■ 3 - Point load shifting system that relieves the degenerative joint and supports
correct knee joint alignment
■ Adjustable straps apply force to single side knee joint to create 3-Point load
shifting system.
■ Patented ROM hinge allows easy and fast range of motion setting, easy to use, tool-free.
■ Extra extension buffer helps to relieve pain and discomfort by slowing down knee
extension movement and avoid knee shock feel near full knee extension,
■ Extension range setting from 0° to 90°, in 15° increments
Flexion range setting from 0° to 105°, in 15° increments
■ Breathable fabric, high quality mesh material provides
SIZE
Knee Circumference ( Left / Right )( Measurements are taken6”(15cm) above mid-patella )
S
13 inch - 15 inch 33 cm - 38 cm
M
15 inch - 17 inch 38 cm - 43 cm
L
17 inch - 19 inch 43 cm - 48 cm
XL
19 inch - 21 inch 48 cm - 53 cm
XXL
21 inch - 23 inch 53 cm - 58 cm
❶There is a brace for left leg and a brace for right leg, check if you have the correct brace before use. For Genu Varum (Bowleg), the ROM hinge should be on the inner side of the knee(Fig. A).❷Unfasten all the hook and loop fasteners. Slide the brace over foot, and pull the brace up to the leg and over the knee(Fig. B).❸Center patella opening on the kneecap and make sure the hinge is positioned on the side of the kneecap(Fig. C).
❹Secure the hoop and loop fastener on the brace and adjust it to desired tightness(Fig. D).
❺ Fasten all the straps according to the sequence indicators (Fig. E), adjust the straps until desired level of support is achieved. While fastening the straps, first, adjust the strap to suitable length at the back and fasten it (Fig. F). Then thread the front end of the strap through the buckles (Fig. G) and secure the hook and loop fasteners at the front. The two middle straps should cross each other (Fig. D). The upper middle strap at the front should be fasten to the lower buckle at the back. The lower middle strap at the front should be fasten to the upper buckle at the back (Fig. H).
ROM setting instruction:
❻For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. I).
❼Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. J).
❽Re-place the Flexion / Extension stops fix cap (Fig. K)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. L).
❾There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. M).
Caution:
1. If discomfort or pain results, persists or increases,discontinue use and consult a hysician.
2. Usage as directed by physician, also operated by professional accroding to physician indication. Do not operate without consulting physician.
3. Make sure the hook and loop fasteners are well fastened while wearing the product. If the hook and loop fasteners cannot be fastened well. stop using the product to prevent injuries.
4. This product is also applicable for Genu Valgum (Knock Knee). However. the ROM hinge should be on the outer side of the knee.
Washing Instructions:
1. Remove foam liner from hinges for hand wash. using a mild detergent and cold water. air dry. Do not wash in washing machine or place in mechanical dryer. Do not bleach nor iron.
2. The splints are removable, please remove the splints before washing.
■ Mild to moderate unicompartmental osteoarthritis
■ Stabilize knee joint
■ Reduce knee pain
■ Genu Varum ( Bowleg )
Features
■ 3 - Point load shifting system that relieves the degenerative joint and supports
correct knee joint alignment
■ Adjustable straps apply force to single side knee joint to create 3-Point load
shifting system.
■ Patented ROM hinge allows easy and fast range of motion setting, easy to use, tool-free.
■ Extra extension buffer helps to relieve pain and discomfort by slowing down knee
extension movement and avoid knee shock feel near full knee extension,
■ Extension range setting from 0° to 90°, in 15° increments
Flexion range setting from 0° to 105°, in 15° increments
■ Breathable fabric, high quality mesh material provides
SIZE
Knee Circumference (Left/Right) ( Measurements are taken6”(15cm) above mid-patella )
S
13 inch - 15 inch 33 cm - 38 cm
M
15 inch - 17 inch 38 cm - 43 cm
L
17 inch - 19 inch 43 cm - 48 cm
XL
19 inch - 21 inch 48 cm - 53 cm
XXL
21 inch - 23 inch 53 cm -58cm
❶There is a brace for left leg and a brace for right leg, check if you have the correct brace before use. For Genu Varum (Bowleg), the ROM hinge should be on the inner side of the knee(Fig. A).
❷Unfasten all the hook and loop fasteners. Slide the brace over foot, and pull the brace up to the leg and over the knee(Fig. B).
❸Center patella opening on the kneecap and make sure the hinge is positioned on the side of the kneecap(Fig. C).
❹Secure the hoop and loop fastener on the brace and adjust it to desired tightness(Fig. D).
❺ Fasten all the straps according to the sequence indicators (Fig. E), adjust the straps until desired level of support is achieved. While fastening the straps, first, adjust the strap to suitable length at the back and fasten it (Fig. F). Then thread the front end of the strap through the buckles (Fig. G) and secure the hook and loop fasteners at the front. The two middle straps should cross each other (Fig. D). The upper middle strap at the front should be fasten to the lower buckle at the back. The lower middle strap at the front should be fasten to the upper buckle at the back (Fig. H).
ROM setting instruction:
❻For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. I).
❼Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. J).
❽Re-place the Flexion / Extension stops fix cap (Fig. K)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. L).
❾There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. M).
Caution:
1. If discomfort or pain results, persists or increases,discontinue use and consult a hysician.
2. Usage as directed by physician, also operated by professional accroding to physician indication. Do not operate without consulting physician.
3. Make sure the hook and loop fasteners are well fastened while wearing the product. If the hook and loop fasteners cannot be fastened well. stop using the product to prevent injuries.
4. This product is also applicable for Genu Valgum (Knock Knee). However. the ROM hinge should be on the outer side of the knee.
Washing Instructions:
1. Remove foam liner from hinges for hand wash. using a mild detergent and cold water. air dry. Do not wash in washing machine or place in mechanical dryer. Do not bleach nor iron.
2. The splints are removable, please remove the splints before washing.
■ Patella stabilization
■ Improve knee joint function
■ Improve knee stability
■ Protect cruciate and collateral ligaments
Features
■ Long length design for additional support.
■ Bilateral ROM hinges provides immobilization to medial and lateral knee instability.
■ Patented ROM hinge allows easy and fast range of motion setting,easy
to use, tool-free.
■ Extra extension buffer helps to relieve pain and discomfort by slowing down
knee extension movement and avoid knee shock feel near full knee extension.
■ Flexion/extension stops kit
■ Extension range setting at 0° ，15° ，30° ，45°，60° ，75°，90°
■ Flexion range setting at 0° ，15° ，30° ，45°，60° ，75°，90°，105°
SIZE
Knee Circumference ( Measurements are taken 6”(15cm) above mid-patella )
S
13 inch - 15 inch 33 cm - 38 cm
M
15 inch - 17 inch 38 cm - 43 cm
L
17 inch - 19 inch 43 cm - 48 cm
XL
19 inch - 21 inch 48 cm - 53 cm
XXL
21 inch - 23 inch 53 cm - 58 cm
THE DEFENDER MESH ROM KNEE BRACE is indicated for cruciate and collateral ligament tears, ligament sprains and meniscus tears.
❶Unfasten all the hook and loop fasteners. Slide the brace over foot, and pull the brace up to the leg and over the knee (Fig. A).❷Center patella opening on the kneecap and make sure the hinges are positioned on both sides of the kneecap (Fig. B).❸Secure the hoop and loop fastener on the brace and adjust it to desired tightness (Fig. C).
❹ Fasten all the straps according to the sequence indicators (Fig. D), adjust the straps until desired level of support is achieved. While fastening the straps, first, adjust the strap to suitable length at the back and fasten it (Fig. E). Then thread the front end of the strap through the buckles (Fig. F) and secure the hook and loop fasteners at the front.
ROM setting instruction:
❺For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. G).
❻Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. H).
❼Re-place the Flexion / Extension stops fix cap (Fig. I)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. J).
❽There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. K).
Caution:
1.If discomfort or pain results, persists or increases,discontinue use and consult a hysician.
2.Usage as directed by physician, also operated by professional accroding to physician indication. Do not operate without consulting physician.
3.Make sure the hook and loop fasteners are well fastened while wearing the product. If the hook and loop fasteners cannot be fastened well. stop using the product to prevent injuries.
Washing Instructions:
1. Remove foam liner from hinges for hand wash. using a mild detergent and cold water. air dry. Do not wash in washing machine or place in mechanical dryer. Do not bleach nor iron.
2. The splints are removable, please remove the splints before washing.
■ Mild to severe ACL and/ or PLC, MCL and LCL instabilities.
Features
■ Anatomic Frame allows the brace to conform to the leg's shape and provide
good support to the patient.
■ Aircraft grade aluminum frame made by 6061 aluminum alloy, provides extra
strength and durability.
■ Light weight and user-friendly smooth edge for comfort and prevents unnecessary
scratch and injury.
■ Tool-free, easy to use Conwell's patented ROM hinge makes it easy and fast to
set range of motion, tool-free.
■ High density foam and soft foam lining for excellent immobilization and comfort.
■ Easy adjustable and removable straps ensure a custom fit.
SIZE
(Measurements are taken (Measurements are taken (Knee width
6”(15cm) above mid-patella) 6”(15cm) below mid-patella)
S
15.5 inch - 18 inch / 12.25 inch - 13.75 inch / 3.5 inch - 4.0 inch
M
18 inch - 20.5 inch / 13.25 inch - 14.75 inch / 4.0 inch - 4.5 inch
L
20.5 inch - 23 inch / 14.25 inch - 15.75 inch / 4.5 inch - 5.0 inch
XL
23.5 inch - 25 inch / 15.25 inch - 16.75 inch / 5.0 inch- 5.5 inch
❶The fastening end of the strap is designed to be removable for the length adjustment purpose. If the strap is too long, remove the hook piece, trim the strap and reapply the hook piece (Fig. A).❷Adjust the foam pads on the straps to suitable position for comfortable wearing. If the foam pad is too long, trim the unwanted part along the groove (Fig. B).❸There are two options for the thickness of the Oval-shaped pads. Choose the required thickness for proper support. ❹For the first time wearing, place the brace to the knee joint and make bilateral ROM mechanisms align with the center of the knee joint. (Fig C). Align the relative positions of ROM mechanisms and knee joint by adjusting anterior straps ①、②. (Refer to the arrow instructions on the straps ) Fasten straps ①、②. (Fig. D). After the alignment is done, for the following wearing, it is not required to unfasten these two straps.
❺ Secure the four posterior straps in sequence of (1)-(4) (Refer to the arrow instructions on the straps) as instructed in (Fig.E Posterior Straps). Press the upper and lower part of the brace while tightening up the straps to provide better fit.ROM setting instruction:
❺For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. F).❻Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in “FLEX” notch, “E ”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. G).❼Re-place the Flexion / Extension stops fix cap (Fig. H)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. I).❽There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. J).
Caution:
1.If discomfort or pain results, persists or increases, discontinue use and consult a physician.
2.Usage as directed by physician, also operated by professional accroding to physician indication. Do not operate without consulting physician.
3.Make sure the hook and loop fasteners are well fastened while wearing the product. If the hook and loop fasteners cannot be fastened well. stop using the product to prevent injuries.
Washing Instructions:
Remove foam liner from hinges for hand wash, using a mild detergent and cold water, air dry. Do not wash in washing machine or place in mechanical dryer. Do not bleach nor iron.
■ Mild to severe ACL and/ or PLC, MCL and LCL instabilities.
Features:
■ Anatomic Frame allows the brace to conform to the leg's shape and provide
good support to the patient.
■ Aircraft grade aluminum frame made by 6061 aluminum alloy, provides extra
strength and durability.
■ Light weight and user-friendly smooth edge for comfort and prevents unnecessary
scratch and injury.
■ Tool-free, easy to use Conwell's patented ROM hinge makes it easy and fast to
set range of motion, tool-free.
■ High density foam and soft foam lining for excellent immobilization and comfort.
■ Easy adjustable and removable straps ensure a custom fit. Size ：S . M . L . XL ( RIGHT )
SIZE
(Measurements are taken (Measurements are taken
6”(15cm) above mid-patella) 6”(15cm) below mid-patella)
S
15.5 inch - 18 inch / 12.25 inch - 13.75 inch / 3.5 inch - 4.0 inch
M
18 inch - 20.5 inch / 13.25 inch - 14.75 inch / 4.0 inch - 4.5 inch
L
20.5 inch - 23 inch / 14.25 inch - 15.75 inch / 4.5 inch - 5.0 inch
XL
23.5 inch - 25 inch / 15.25 inch - 16.75 inch / 5.0 inch - 5.5 inch
❶The fastening end of the strap is designed to be removable for the length adjustment purpose. If the strap is too long, remove the hook piece, trim the strap and reapply the hook piece (Fig.A).
❷Adjust the foam pads on the straps to suitable position for comfortable wearing. If the foam pad is too long, trim the unwanted part along the groove (Fig.B).
❸There are two options for the thickness of the Oval-shaped pads. Choose the required thickness for proper suppor.
❹For the first time wearing, place the brace to the knee joint and make bilateral ROM mechanisms align with the center of the knee joint. (Fig.C). Align the relative positions of ROM mechanisms and knee joint by adjusting anterior straps ①、②. (Refer to the arrow instructions on the straps ) Fasten straps ①、②. (Fig.D). After the alignment is done, for the following wearing, it is not required to unfasten these two straps.
❺ Secure the four posterior straps in sequence of (1)-(4) (Refer to the arrow instructions on the straps) as instructed in (Fig.E Posterior Straps). Press the upper and lower part of the brace while tightening up the straps to provide better fit.
ROM setting instruction:
❺For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. F).
❻Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. G).
❼Re-place the Flexion / Extension stops fix cap (Fig. H)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. I).
❽There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. J).
Caution:
1.If discomfort or pain results, persists or increases, discontinue use and consult a physician.
2.Usage as directed by physician, also operated by professional accroding to physician indication. Do not operate without consulting physician.
3.Make sure the hook and loop fasteners are well fastened while wearing the product. If the hook and loop fasteners cannot be fastened well. stop using the product to prevent injuries.
Washing Instructions:
detergent and cold water, air dry.Do not wash in washing machine or place in mechanical dryer. Do not bleach nor iron.
❶There is a brace for left leg and a brace for right leg, check if you have the correct brace before use. For Genu Varum (Bowleg), the ROM hinge should be on the inner side of the knee(Fig. A).❷Unfasten all the hook and loop fasteners. Slide the brace over foot, and pull the brace up to the leg and over the knee(Fig. B).❸Center patella opening on the kneecap and make sure the hinge is positioned on the side of the kneecap(Fig. C).
❹Secure the hoop and loop fastener on the brace and adjust it to desired tightness(Fig. D).
❺ Fasten all the straps according to the sequence indicators (Fig. E), adjust the straps until desired level of support is achieved. While fastening the straps, first, adjust the strap to suitable length at the back and fasten it (Fig. F). Then thread the front end of the strap through the buckles (Fig. G) and secure the hook and loop fasteners at the front. The two middle straps should cross each other (Fig. D). The upper middle strap at the front should be fasten to the lower buckle at the back. The lower middle strap at the front should be fasten to the upper buckle at the back (Fig. H).
ROM setting instruction:
❻For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. I).
❼Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. J).
❽Re-place the Flexion / Extension stops fix cap (Fig. K)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. L).
❾There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. M).
❶Unfasten all the hook and loop fasteners. Slide the brace over foot, and pull the brace up to the leg and over the knee (Fig. A).❷Center patella opening on the kneecap and make sure the hinges are positioned on both sides of the kneecap (Fig. B).❸Secure the hoop and loop fastener on the brace and adjust it to desired tightness (Fig. C).
❹ Fasten all the straps according to the sequence indicators (Fig. D), adjust the straps until desired level of support is achieved. While fastening the straps, first, adjust the strap to suitable length at the back and fasten it (Fig. E). Then thread the front end of the strap through the buckles (Fig. F) and secure the hook and loop fasteners at the front.
ROM setting instruction:
❺For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. G).
❻Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in“FLEX” notch, “E”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. H).
❼Re-place the Flexion / Extension stops fix cap (Fig. I)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. J).
❽There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. K).
❶The fastening end of the strap is designed to be removable for the length adjustment purpose. If the strap is too long, remove the hook piece, trim the strap and reapply the hook piece (Fig. A).❷Adjust the foam pads on the straps to suitable position for comfortable wearing. If the foam pad is too long, trim the unwanted part along the groove (Fig. B).❸There are two options for the thickness of the Oval-shaped pads. Choose the required thickness for proper support. ❹For the first time wearing, place the brace to the knee joint and make bilateral ROM mechanisms align with the center of the knee joint. (Fig C). Align the relative positions of ROM mechanisms and knee joint by adjusting anterior straps ①、②. (Refer to the arrow instructions on the straps ) Fasten straps ①、②. (Fig. D). After the alignment is done, for the following wearing, it is not required to unfasten these two straps.
❺ Secure the four posterior straps in sequence of (1)-(4) (Refer to the arrow instructions on the straps) as instructed in (Fig.E Posterior Straps). Press the upper and lower part of the brace while tightening up the straps to provide better fit.ROM setting instruction:
❺For ROM ( range of motion ) setting, take off the Flexion / Extension stops fix cap by gently unlocking the cap from the bottom using the fingers(Fig. F).❻Select the correct Flexion and Extension stops, place them into the notches according to the FLEX/EXT marks on the hinge,“F” stops in “FLEX” notch, “E ”stops in “EXT” notch. For easier application, place the shorter Flexion / Extension stop before the longer Flexion / Extension stop. Take out the longer stop before the shorter one(Fig. G).❼Re-place the Flexion / Extension stops fix cap (Fig. H)., place the cap on the hinge accordingly to FLEX / EXT marks. Make sure the bolts on the cap are well fixed to the holes, then have the ends of the cap well locked to the hinge (Fig. I).❽There are two extension buffer stops with 15°and 25°. Those extra buffer stops are designed to help relieve pain and discomfort by slowing down knee extension movement and avoid knee shock feel near full knee extension. Bigger extension range buffer stop (25°) or smaller extension range buffer stop (15°) can be selected according to individual requirement(Fig. J).
